View Rule

View EO 12866 Meetings Printer-Friendly Version     Download RIN Data in XML

EPA/SWER RIN: 2050-AE01 Publication ID: Fall 2004 
Title: NESHAPS: Standards for Hazardous Air Pollutants for Hazardous Waste Combustors (Phase I Final Replacement Standards and Phase II) 
Abstract: On September 30, 1999, EPA promulgated standards to control emissions of hazardous air pollutants from incinerators, cement kilns, and lightweight aggregate kilns that burn hazardous waste (referred to as the Phase I Rule). A number of parties, representing interests of both industry and the environmental community, sought judicial review of the rule. The Court ruled against EPA and vacated the Phase I rule. On October 19, 2001, EPA, together with all petitioners, filed a joint motion asking the Court to stay the issuance of its mandate to allow them time to develop interim standards. These stop-gap interim standards were promulgated on February 13 and 14, 2002. They replace the vacated standards temporarily, until revised replacement standards are promulgated by June 14, 2005. EPA will ultimately finalize the Phase I replacement standards. Also, EPA is developing emission standards for hazardous waste burning industrial, institutional, commercial boilers, process heaters, and hydrochloric acid production furnaces. These sources are referred to as Phase II Sources because the standards were originally scheduled to be promulgated after Phase I source standards were finalized; however, a separate consent decree now requires us to finish developing emission standards for the Phase II sources by the same date as those for Phase I (June 14, 2005). EPA has developed options for calculating the emission standards that are considered to be consistent with both the statutory requirements and the opinion of the Court. EPA has proposed emission standards and compliance provisions for both the Phase I and Phase II sources. 
Agency: Environmental Protection Agency(EPA)  Priority: Other Significant 
RIN Status: Previously published in the Unified Agenda Agenda Stage of Rulemaking: Final Rule Stage 
Major: No  Unfunded Mandates: No 
CFR Citation: 40 CFR 63    40 CFR 264    40 CFR 265    40 CFR 266    40 CFR 270   
Legal Authority: 42 USC 6924 RCRA 3004    42 USC 6925 RCRA 3005    42 USC 7412 CAA 112    42 USC 7414 CAA 114   
Legal Deadline:
Action Source Description Date
Final  Judicial  Consent decree.  06/14/2005 
NPRM  Judicial  Consent decree for Phase 2 portion of rule.  03/31/2004 

Statement of Need: Section 112 of the Clean Air Act requires that the EPA promulgate regulations requiring the control of hazardous air pollutants from major and certain area sources. The control of hazardous air pollutants is achieved through promulgation of emission standards under sections 112(d) and (f) and, in appropriate circumstances, work practice standards under section 112(h). On September 30, 1999 EPA promulgated standards to control emissions of hazardous air pollutants from incinerators, cement kilns, and lightweight aggregate kilns that burn hazardous waste (referred to as the Phase I Rule). A number of parties, representing interests of both industry and the environmental community, sought judicial review of the rule. The Court ruled against EPA and vacated the Phase I rule.

Summary of the Legal Basis: On October 19, 2001, EPA, together with all petitioners, filed a joint motion asking the Court to stay the issuance of its mandate to allow time to develop interim standards. These stop-gap interim standards were promulgated on February 13 and 14, 2002. They replace the vacated standards temporarily, until revised replacement standards are promulgated by June 14, 2005. EPA is working towards promulgation by this date. EPA is also developing emission standards for hazardous waste burning industrial, institutional, commercial boilers, process heaters, and hydrochloric acid production furnaces. These sources are referred to as Phase II Sources because the standards were originally scheduled to be promulgated after Phase I source standards were finalized; however, a separate consent decree now requires us to finish developing emission standards for the Phase II sources by the same date as those for Phase I (June 14, 2005).

Alternatives: EPA has developed several options for calculating the emission standards and has included these options in the April 20, 2004 proposal.

Anticipated Costs and Benefits: Estimated costs and benefits for the proposed standards are summarized in the April 20, 2004 proposal.

Risks: For the 1999 rule, we estimated the avoided incidence of mortality and morbidity associated with reductions in particulate matter (PM) emissions. Estimates of cases of mortality and morbidity avoided were made for children and the elderly, as well as the general population, using concentration-response functions derived from human epidemiological studies. Morbidity effects included respiratory and cardiovascular illnesses requiring hospitalization, as well as other illnesses not requiring hospitalization, such as acute and chronic bronchitis and acute upper and lower respiratory symptoms. For this rule, we are comparing characteristics of the sources covered by the 1999 rule to the sources covered by the replacement rule that are related to risk. These characteristics include emissions, stack characteristics, meteorology, and population. Based on the results of the statistical comparisons, we will infer whether the risks will be about the same, less than, or greater than the 1999 rule. Risk inferences for boilers and HCl production furnaces will be based on comparisons with incinerators for the 1999 rule. The risk estimates for the proposed standards are summarized in the April 20, 2004 proposal.

Timetable:
Action Date FR Cite
NPRM-CK  04/19/1996  61 FR 17358   
Final-Fasttrack  06/19/1998  63 FR 33782   
Final-CK  09/30/1999  64 FR 52828   
NODA  07/27/2000  65 FR 39581   
DF 1  07/03/2001  66 FR 35087   
NPRM-Phase1  07/03/2001  66 FR 35126   
Parallel Proposal  07/03/2001  66 FR 35124   
Direct Final Action  10/15/2001  66 FR 52361   
Final Compliance Exten.  12/06/2001  66 FR 63313   
Interim Final Action  02/13/2002  67 FR 6792   
Final HAP  02/14/2002  67 FR 6968   
NPRM-Phases 1&2  04/20/2004  69 FR 21197   
Final Action  06/00/2005    
Additional Information: SAN No. 3333, EDocket No. OAR-2004-0022; For information on the Phase I portion of this effort, see SAN 4418, RIN 2050-AE79.
Regulatory Flexibility Analysis Required: No  Government Levels Affected: Federal, State, Tribal 
Small Entities Affected: Businesses  Federalism: No 
Included in the Regulatory Plan: Yes 
RIN Information URL: www.epa.gov/hwcmact/  
Sectors Affected: 3335 -; 3343 Audio and Video Equipment Manufacturing; 3251 Basic Chemical Manufacturing; 3273 Cement and Concrete Product Manufacturing; 3271 Clay Product and Refractory Manufacturing; 3328 Coating, Engraving, Heat Treating and Allied Activities; 3342 Communications Equipment Manufacturing; 3341 Computer and Peripheral Equipment Manufacturing; 2211 Electric Power Generation, Transmission and Distribution; 45431 Fuel Dealers; 3332 Industrial Machinery Manufacturing; 3274 Lime, Gypsum and Gypsum Product Manufacturing; 3327 Machine Shops, Turned Product, and Screw, Nut and Bolt Manufacturing; 3362 Motor Vehicle Body and Trailer Manufacturing; 3361 Motor Vehicle Manufacturing; 3363 Motor Vehicle Parts Manufacturing; 2123 Non-Metallic Mineral Mining and Quarrying; 3259 Other Chemical Product Manufacturing; 3329 Other Fabricated Metal Product Manufacturing; 3339 Other General Purpose Machinery Manufacturing; 3279 Other Nonmetallic Mineral Product Manufacturing; 3255 Paint, Coating, Adhesive, and Sealant Manufacturing; 3253 Pesticide, Fertilizer and Other Agricultural Chemical Manufacturing; 3241 Petroleum and Coal Products Manufacturing; 4227 Petroleum and Petroleum Products Wholesalers; 3254 Pharmaceutical and Medicine Manufacturing; 3231 Printing and Related Support Activities; 5629 Remediation and Other Waste Management Services; 3252 Resin, Synthetic Rubber, and Artificial and Synthetic Fibers and Filaments Manufacturing; 3344 Semiconductor and Other Electronic Component Manufacturing; 22132 Sewage Treatment Facilities; 5622 Waste Treatment and Disposal 
Agency Contact:
Michael Galbraith
Environmental Protection Agency
Solid Waste and Emergency Response
5303P,
Washington, DC 20460
Phone:703 605-0567
Fax:703 308-8686
Email: galbraith.michael@epa.gov

Frank Behan
Environmental Protection Agency
Solid Waste and Emergency Response
Mail Code 5304T, 1200 Pennsylvania Avenue NW,
Washington, DC 20460
Phone:202 566-1730
Email: behan.frank@epa.gov